Pick and Place Tabletop
NeoDen4 Pick and place tabletop Video
NeoDen4 Pick and place tabletop
Feature
The fourth-generation model NeoDen4 is NeoDen Tech's independent product, with completely independent intellectual property. Its high precision vision system made it stand out in desktop pick and place machine area.
This manual cover installation, setup, customization and operation of the NeoDen4 pick and place machine. Please read this manual in its entirety before working on the machine.
Specification
| Product name | NeoDen4 Pick and place tabletop |
|
Machine Style |
Single Gantry with 4 Heads |
|
Placement Rate |
4000CPH |
|
External Dimension |
L 680*W 870*H 460mm |
|
Max applicable PCB |
290mm*1200mm |
|
Feeders |
48pcs |
|
Average working power |
220V/160W |
|
Component Range |
Smallest Size: 0201 |
|
Biggest Size: TQFP240 |
|
|
Max Height: 5mm |
Details
NEODEN independent research and development on-line dual rails
Machines equipped with the auto-loading rail system can accommodate boards from to in width, and in length.
The rail system allows automatic feeding of PCBs, automatic alignment of the board with the camera, and automatic ejection from the front of the machine or the rear.
Four high precision nozzles
1. Any size nozzle can be installed in any of the four locations in the head, so a single machine can handle all of the necessary components without the need for nozzle changes.
2. The mounting head was designed in a suspended, fully symmetric and high degree of coupling way, ensure it can mount components with higher space, more gentle and more efficient equipped with four high precision mounting heads, mount at the same time with 360 degrees rotation at -180 to 180.
Vision system
The downward-looking camera
On the head is used for precision location of feeders and PCB placement points.
The upward-looking camera
If the camera detects the absence of a component, the machine will make up to two additional attempts to pick a component before asking the user for further instructions.
48 8mm tape-and-reel feeders
The electric feeders are inexpensive but sophisticated microprocessor controlled units paired will tape peelers.
The NeoDen4 can accommodate up to 48 8mm tape-and-reel feeders on its left and right rails, and any size feeder (8, 12, 16 and 24mm) can be installed in any combination or order on the left and right sides of the machine.
The vibration feeder (included) can handle up to 5 separate tubes.
The amount of space available for tray-fed components and short tapes depends on the available real estate on the table.
Package
Feeder and peeler installation
The feeders are installed on the lower rails, and the peelers are installed on the upper rails. Each is attached with a single Allen screw, and connected with a single cable.
The feeders are connected with 4-pin cables, and are addressed digitally over a data bus.
It therefore does not matter which feeder is plugged into which port – the feeder ID code determines which feeder will be activated.
On the other hand, peelers are addressed with analog power signals. Therefore, activation of a peeler depends entirely on the two-pin port to which it is connected.
The software interface allows the user to assign different combinations of peeler and feeder IDs when it is desired to use a feeder with a certain ID in a position that corresponds to a different peeler ID.
Notes
The machine will start a 1-2 mins self- inspection after boot-up. It enters the operation page once finished.
Need to wait 1-2 minutes after turn on the machine, mounting head will move diagonally and then enter into operation page.
Power off after the software being turned off, which decrease the damage to the software.
Provide one-stop SMT assembly production line
FAQ
Q1. Are you a trade company or a manufacturer?
A: We are an professional manufacturer specialized in SMT Machine, Pick and Place Machine, Reflow Oven, Screen Printer, SMT Production Line and other SMT Products.
Q2. What's the way of shipping?
A: These are all heavy machines.
We suggest you use cargo ship.
But components for mending the machines, air transportation would be fine.
Q3. MOQ?
A: 1 set machine, mixed order is also welcomed.
About us
exhibition
certifications
factory
If you need, please feel free to contact us!
Hot Tags: pick and place tabletop, China, manufacturers, suppliers, wholesale
Send Inquiry
