+86-571-85858685

High-power PCB Thermal Management Approach

Jul 06, 2022

The entire power electronics industry, including RF applications and systems involving high-speed signals, is moving toward solutions that provide increasingly complex functionality in ever-smaller spaces. Designers are faced with increasingly demanding challenges in meeting the requirements of system size, weight and power, including effective thermal management, which in turn begins with the design of the PCB.

Highly integrated active power devices (e.g., MOSFET transistors) emit large amounts of heat, requiring PCBs that can transfer heat from the hottest components to the ground or heat sink surface to operate as efficiently as possible. Thermal stress is one of the main causes of power device failure, as it can cause performance degradation and may even lead to system failure or malfunction. The rapid growth of device power density and increasing frequency are the main causes of overheating in electronic components. While semiconductors with lower power loss and better thermal conductivity, such as wide band materials, are being used more and more extensively, they are not sufficient by themselves to eliminate the need for effective thermal management.

Current silicon-based power devices can be achieved at junction temperatures between about 125°C and 200°C. However, it is desirable to always allow the device to operate without exceeding this limiting condition, thus avoiding rapid aging of the device and shortening its remaining lifetime. In fact, it is estimated that if improper thermal management leads to a 20°C increase in operating temperature, the resulting reduction in the remaining life of the component will be as much as 50%.

Layout Wiring (layout) Methodology

A common thermal management method used in many projects is the use of a standard flame retardant class 4 (FR-4) substrate, which is an inexpensive and easy to process material that focuses on thermal optimization of the circuit layout.

The main measures used involve providing additional copper surfaces, using thicker alignments, and inserting heat sinks under the components that generate the most heat. A more radical technique to dissipate more heat involves inserting or applying a real copper block to the PCB or to the outermost layer, which is usually in the shape of a coin, hence the name "copper coin". After processing the copper coin separately, it can be soldered or directly attached to the PCB, or it can be inserted into the inner layer and connected to the outer layer through the heat sink. The PCB shown in Figure 1 is made in a special cavity to accommodate a copper coin.

Pic1

Copper has a thermal conductivity of 380 W/mK, compared to 225 W/mK for aluminum and 0.3 W/mK for FR-4. Copper is a relatively inexpensive metal that has been widely used in PCB manufacturing; therefore, it is ideal for making copper coins, heat sink holes, and ground layers - all solutions that improve heat dissipation.

The correct placement of active devices on the board is a key factor in preventing hot spots from forming, thus ensuring that heat is distributed as evenly as possible across the board. In this regard, the active devices should be distributed around the PCB in no particular order, thus avoiding the formation of hot spots in specific areas. However, it is best to avoid placing active devices that generate a lot of heat near the edge of the board. Instead, they should be placed as close as possible to the center of the board, thus facilitating uniform heat distribution. If high-power devices are installed near the edge of the board, they will accumulate heat at the edge, thus increasing the local temperature. On the other hand, if they are placed near the center of the board, the heat will be distributed in all directions along the surface, making it easier to reduce the temperature and make it easier to distribute heat. Power devices should not be placed close to sensitive components and should be properly spaced from each other.

Measures taken at the layout level can be further improved by using active cooling and passive cooling systems (such as heat sinks or fans) - such systems can remove heat from active devices, rather than emitting it directly into the board. In general, designers must find the right compromise between different thermal management strategies, depending on the requirements of the particular application and the available budget.

PCB Substrate Selection

FR-4 is typically not suitable for applications that require the dissipation of large amounts of heat due to its low thermal conductivity (between 0.2 and 0.5 W/mK). The heat generated in high-power circuits can be considerable, and these systems often operate in harsh environments and extreme temperatures. Using an alternative substrate material with higher thermal conductivity may be a better choice than using traditional FR-4.

Ceramic materials, for example, offer significant advantages for thermal management of high-power PCBs. Such materials, in addition to improving thermal conductivity, also have excellent mechanical properties and thus help compensate for the stresses accumulated during repeated thermal cycling. In addition, ceramic materials have a low dielectric loss at frequencies up to 10 GHz. For higher frequencies, it is always possible to choose hybrid materials (e.g. PTFE), which provide the same low losses but with a moderate reduction in thermal conductivity.

The higher the thermal conductivity of the material, the faster the heat transfer. Thus, in addition to being lighter than ceramics, metals such as aluminum offer an excellent solution for transferring heat away from components. Aluminum in particular is also an excellent conductor, has excellent durability, is recyclable, and is non-toxic. Due to its high thermal conductivity, the metal layer helps transfer heat quickly throughout the board. Some manufacturers also offer metal-clad PCBs where both outer layers are metal-clad, usually aluminum or galvanized copper. Aluminum is the best choice from a cost-per-weight perspective, while copper has a higher thermal conductivity. Aluminum is also widely used to make PCBs that support high-power LEDs (as shown in the example in Figure 2), where its ability to reflect light away from the substrate is also particularly useful.

pic2

Even silver, due to its thermal conductivity of about 5% higher than copper, can also be used to create alignments, vias, pads and metal layers. In addition, if the board is used in a humid environment where toxic gases exist, the use of silver finishes on bare copper alignments and copper solder pads will help prevent corrosion - a typical threat known in such environments.

Metal PCBs, also known as insulated metal substrates (IMS), can be laminated directly into the PCB to form boards with FR-4 substrates and metal cores. Single and double layer technologies are used, with depth-controlled wiring, whereby heat can be transferred from on-board components to less critical areas. In IMS PCBs, a thin layer of thermally conductive but electrically insulating dielectric is laminated between a metal substrate and a copper foil. The copper foil is etched into the desired circuit pattern and the metal substrate absorbs heat from the circuit through this thin dielectric.

The main advantages offered by IMS PCBs are as follows.

-Significantly higher heat dissipation than standard FR-4 structures.

-The thermal conductivity of the dielectric is typically 5 to 10 times higher than that of ordinary epoxy glass.

-The efficiency of heat transfer is much higher than that of conventional PCBs.

In addition to LED technology (illuminated signs, displays and lighting), IMS PCBs are widely used in the automotive industry (headlights, engine controls and power steering), power electronics (DC power supplies, inverters and engine controls), switches and semiconductor relays.

Send Inquiry