Electronic devices will generate a certain amount of heat when working, so that the internal temperature of the device rises rapidly, if the heat is not distributed in a timely manner, the device will continue to heat up, the device will fail due to overheating, the reliability of electronic equipment performance will be reduced. Therefore, a good thermal treatment of the circuit board is very important. PCB board heat dissipation is a very important link, then PCB board heat dissipation techniques are how, we discuss the following.
Method-1
Heat dissipation through the PCB board itself. Currently widely used PCB board is a copper / epoxy glass cloth substrate or phenolic resin glass cloth substrate, there are a small number of paper-based copper laminate used. Although these substrates have excellent electrical properties and processing performance, but poor heat dissipation, as a high heat generation components of the heat dissipation path, almost can not be expected to conduct heat by the PCB itself resin, but from the surface of the component to the surrounding air heat dissipation. However, as electronic products have entered the era of miniaturised components, high density mounting and high heat generation assembly, it is not enough to rely on the surface of components with a very small surface area to dissipate heat. At the same time, due to the large number of surface-mounted components such as QFPs and BGAs, the heat generated by the components is transmitted to the PCB in large quantities. Therefore, the best solution to heat dissipation is to improve the thermal capacity of the PCB itself, which is in direct contact with the heat-generating components, and to conduct it out or distribute it through the PCB.
PCB layout recommendations:
Heat sensitive devices are placed in the cold air area. Temperature detecting devices are placed in the hottest locations.
The devices on the same printed board should be arranged as far as possible according to their heat generation and heat dissipation degree, with devices that generate little heat or have poor heat resistance (such as small signal transistors, small-scale integrated circuits, electrolytic capacitors, etc.) placed in the uppermost stream (at the entrance) of the cooling airflow, and devices that generate a lot of heat or have good heat resistance (such as power transistors, large-scale integrated circuits, etc.) placed in the most downstream of the cooling airflow. In the horizontal direction, high-power devices are arranged as close as possible to the edge of the printed board in order to shorten the heat transfer path; in the vertical direction, high-power devices are arranged as close as possible to the top of the printed board in order to reduce the impact of these devices on the temperature of other devices when working. The heat dissipation of the printed board in the equipment mainly relies on air flow, so the air flow path should be studied during the design and the devices or printed circuit boards should be configured reasonably. Air flow always tends to flow where there is less resistance, so when configuring devices on the printed circuit board, avoid leaving a large void in a certain area. The same applies to the configuration of multiple boards in a complete machine. Devices that are more sensitive to temperature are best placed in the lowest temperature area (e.g. the bottom of the device), never place it directly above a heat generating device, and multiple devices are best staggered in a horizontal plane. Place the devices with the highest power consumption and highest heat generation near the best locations for heat dissipation. Do not place higher heat generating devices in the corners and around the edges of the printed board unless there is a heat sink near it. Choose larger devices where possible when designing power resistors and adjust the layout of the board so that there is sufficient space for heat dissipation.
Method-2
High heat-generating devices plus heat sink, thermal conductivity board when there are a few devices in the PCB when the heat generation is large (less than 3), you can add heat sink or thermal conductivity tube on the heat-generating devices, when the temperature still can not be lowered, you can use a heat sink with a fan to enhance the heat dissipation effect. When there are more heat generating devices (more than 3), a large heat sink (board) can be used, which is a special heat sink tailored to the position and height of the heat generating devices on the PCB board or a large flat heat sink with different component height positions keyed in. The heat sink is then snapped onto the component surface as a whole, making contact with each component and dissipating the heat. However, the heat sink is not very effective due to the poor consistency of the height of the components when they are soldered together. Usually a soft thermal phase change pad is added to the component surface to improve the heat dissipation.
Method-3
For equipment with free convection air cooling, it is best to arrange the integrated circuits (or other devices) in a longitudinal fashion or in a long horizontal fashion.

